Odyssey's custom-designed Par Ends come standard with all of their grips. Its special plastic composite will not shatter like cheap bar ends do, and they’re very lightweight. The Par End is a combination of the over-the-bar-style cap and the inside-the-bar-style to prevent the inner portion from blowing out like it does on ordinary press-fit bar ends. Comes stock on all of Odyssey's grips.
When you can’t even see a part, you might forget about it, but it doesn’t mean its not important. Flat tires are probably the most common bicycle failures. Many times, flats are caused by the rims, specifically the lack of protection from the rims' sharp edges. Good rim strips didn’t exist for BMX rims. They work well and improve the function of any 20 inch rim. If you forget about them, that means they are doing their job.
Compatible cable for M2 Monolever.
The Gost pads feature a unique design to make install and set up easier. - Improved stiffness by built in toe-in into the pad shape and using a solid extruded aluminum frame - Assembly is simplified by lining up the rim and tightening a M6 female bolt
Upper Cable Only - 3 Sizes 390mm - Short 425mm - Medium 475mm - Long Odyssey's original dual cable detangler system has been the industry standard since day one. Odyssey has been making the Gyro® since 1986 and constantly improving it along the way. KEY FEATURES Short, Medium, or Long to fit a range of handlebar sizes Fits most detangler systems Designed specifically for GTX-S and G3 Gyros®
Odyssey's original dual cable detangler system has been the industry standard since day one. Odyssey has been making the Gyro® since 1986 and constantly improving it along the way. KEY FEATURES Longer length to fit larger, modern handlebars Fits most detangler systems Designed specifically for GTX-S and G3 Gyros®
The Slim by Four brake pads feature a symmetric shape designed for both forwards and backwards braking. - Custom inner frame helps to stiffen the pad, reducing braking power loss from flex
Lower Cable only Odyssey's original dual cable detangler system has been the industry standard since day one. Odyssey has been making the Gyro® since 1986 and constantly improving it along the way. Universal fit. Available in Black and White.
Replacement non-drive side sealed cartridge ball bearing for Clutch v1/v2 freecoaster hub. 6003RS.
Sealed 7905RS Bearing This goes in the hub shell's Drive side, the driver moves on this. Replacement part direct from Odyssey
The Odyssey K-Shield Linear cable features a pre-stretched inner Slic Kable covered in a linear casing to prevent binding and an outer K-Shield mesh housing for less weight over a standard steel mesh housing (2.9 oz). - Black - 60 – 65mm
Unique dual shot injection process allows an extra soft and thin feel, with a harder secondary inner layer that helps resist tearing Updated keyboard style surface with emojis hand picked by the Boss himself, Aaron Ross. Includes Odyssey Par End end plugs Length 165mm
As the name implies, this new version can be easily adjusted to cover 3 different lengths by utilizing the cable’s unique straddle interface connection. This tool-free feature allows the Adjustable Quik Slic Kable to be a one-size-fits-all cable for virtually every braking configuration. FEATURES - Adjustable hanger slot allows upper cable to rotate for optimum alignment. - The integrated hanger and straddle cable creates direct routing to brake arms with no bends or twists to reduce flex. - Linear K-Shield mesh housing offers higher compression rate and lighter weight than standard steel mesh. - All Odyssey Linear cables are offered with the K-Shield housing. - Specially designed and machined Volcano ferrules prevent premature housing blowout. Velcro strap included. SPECS - Housing length: 995mm - Frame requirements: Slotted cable stop and guides. 245mm (+/-3) distance from center brake boss to the front of the cable stop is recommended. - Brake requirements: Open-ended U-brake arms. - Works with most brake levers. - Velcro strap included.
The Springfield lever features an easy to install and remove design. - Easy to install and remove without having to wrestle grips on and off - Die-cast clamp design
$18.00 - $20.00
Odyssey Twisted PC pedals-extremely simple, lightweight, inexpensive and famously durable plastic-bodied design.Often duplicated but never replicated. - High-strength plastic composite
The newest addition to the Odyssey accessories lineup are LED Bike Lights. These easy to install/remove lights will be sold in pairs (front & rear) and have two functions (flashing & constant). These lights will help you stay safe while still cruising the streets. SPECS -125mm x 26.5mm x 22.5mm -Fits on 18mm to 32mm diameter tubing. -CR2032 Battery (1)
Odyssey Bluebird chain is the proven and reliable KMC 510-HX chain with an added a permanently attached, factory installed half-link to one end. When the chain is trimmed to size you can easily decide whether or not to use the half-link. Original factory assembled pin joints are radically stronger than workshop assembled ones, so this is a huge benefit. - Proven and reliable KMC 510-HX chain - Factory installed half-link for a radically stronger set-up
Odyssey's original dual cable detangler system has been the industry standard since day one. Odyssey has been making the Gyro since 1986 and constantly improving it along the way. -Everything you need to run a Gyro. -Odyssey Gyro cables: Upper (425mm) and lower (universal) included
This custom 7075-T6 aluminum pre-load bolt design is included with every Odyssey fork. - Fits both a 6mm and 8mm allen key. - Front brake cable thru-way hole for removal without disconnecting brake hardware. - Designed with an easy-cut thread groove if you cut your fork’s steerer tube down.
The Odyssey Springfield brake features a one spring design to make brake installation and set up simple and easy. - For rear use only
One of the most successful and popular pedals, and for good reason. The original Twisted PC is extremely simple, lightweight, inexpensive and famously durable plastic-bodied design. Often duplicated but never replicated. KEY FEATURES High-strength nylon composite 16 pins per side Traditional looseball bearings Chromoly spindle SPECS Spindle: 9/16" Width: 98mm Length: 89mm
$22.00 - $25.00
-For Mid BB BMX Frames -Comes with all necessary spacers -Professional installation recommended to extend bearing life -Select size based on your crank's spindle size LIMITED EDITION - New Colors Added as they arrive :)
The Odyssey Medium Monolever is a favorite with its familiar feel, smooth edges and variety of handle options. - Fits 7/8" bars, has a hinged bracket, and does not include cable knarps
The Tom Dugan signature Grandstand pedals feature a slim design to keep feet close to the axle, plus a wider, dual-concave platform. - 17mm thick at center - 105mm wide - Full-size 14mm heat-treated axle with 17mm wrench flats and 6mm broach - 9/16"
The M2 lever works with a single cable or Odyssey's dual cable system. - Includes M2 dual cable, double cable coupler and single cable coupler - Replaceable hardware to eliminate stripping
-For Mid BB BMX Frames -Comes with all necessary spacers -Professional installation recommended to extend bearing life -Select size based on your crank's spindle size -Other Limited Edition colors available (sometimes)
$28.00 - $33.00
Broc Raiford signature tire. Odyssey worked closely with Broc to dial in a tread that meets his riding needs while remaining simple and stylish. Odyssey's R-Grip rubber compound ensures superior grip and wear resistance. - Large Directional tread pattern - Odyssey R-Grip rubber compound - Superior grip & wear resistance - Micro knurling throughout - NOTE: Yes, it squeaks
Designed using high-quality sealed bearings and a precision tapered wedge to keep the headset tight at all times. FEATURES - High-quality sealed bearings. - Color matched spacers included. - 10mm, 3mm and 2mm (15mm total) - Laser etched Odyssey bearings. SPECS - Campagnolo standard spec. - 1-1/8 integrated headset. - 45º tapered bearings 41.8mm outer diameter (fits 42mm BMX head tubes).
New dust cap design, with Monogram laser etched logo, for a cleaner look to accommodate a taller riding set up with less spacers. Same quality as Odyssey's Pro Headset using high-quality sealed bearings and a precision tapered wedge to keep the headset tight at all times. FEATURES - High-quality sealed bearings. - Color matched spacers included. - 15mm dust cap. With 3mm, and 2mm spacers - Laser etched Odyssey bearings. SPECS - Campagnolo standard spec. - 1 1/8-inch integrated headset. - 45º tapered bearings - 41.8mm outer diameter (fits 42mm BMX head tubes).
The Mike Aitken signature BMX seat is a stylish and durable, that's tear and scuff resistant.
Page 1 of 2 Next page